고전압 저항기

Standard quotation response within 6 hours · typical resistor lead time about 3 weeks · samples for evaluation on request.

HVC manufactures high voltage thick film resistors in three form factors: planar leaded (flat) to 35 kV, cylindrical leaded (tube) to 60 kV, and power bar (screw terminal) to 150 kV and 110 W. Resistance runs from 200 Ω to 1 TΩ, tolerance from ±0.1%, and every construction is non-inductive.

The form factor decides what the resistor can do. A planar part puts the resistance track on a flat alumina substrate and spreads heat over an area; a tube part winds the track around a ceramic cylinder and fits into an axial space; a power bar carries the heat into a large ceramic body with metal caps and screw terminals. This page maps the three families onto voltage, resistance, power and mounting, then links to the detailed specification pages.

The three form factors at a glance

폼 팩터건설전압저항설치
Planar leaded (flat)
HVR-GHP
Thick film on flat alumina, epoxy / silicone / polyimide coating최대 35kV200 Ω – 1 TΩPCB pins, radial
Cylindrical leaded (tube)
HVR-BSP / HVR-BOP
Thick film on ceramic tube, silicone coating최대 60kV200Ω – 1GΩAxial leads, 3.5 / 7.0 mm body
Power bar (rod)
HVR-PFS
Thick film on cylindrical ceramic, nickel-plated copper caps80~150kV200Ω – 1GΩScrew / M8 cap, 14–45 mm bar

Surge and energy absorption duty is covered by a separate family: high energy ceramic disc resistors, built to absorb a defined energy pulse rather than hold a steady voltage.

How the three resistor bodies behave in a circuit

A high voltage resistor is not selected by resistance value alone. The body has to survive the electric field, move heat out of the film, and remain mechanically stable while the circuit is energised. The planar HVR-GHP family is the compact choice when the board needs a short radial path and the designer needs fine trimming or a very high resistance value. Its flat ceramic substrate spreads the film over an area, so the thermal path is broad and the part can be specified with epoxy, high-temperature silicone or polyimide-style protection depending on the environment.

The HVR-BSP HVR-BOP cylindrical families use a ceramic tube with axial leads. The round body is useful where the resistor sits in a multiplier, probe, voltage divider or insulated sleeve. The 3.5 mm and 7.0 mm body options allow the mechanical envelope to be controlled without moving to a large power resistor. This construction is especially practical when the resistance is high, the continuous power is moderate and the customer needs a leaded part rather than a screw-mounted component.

The HVR-PFS power bar is different. Its large ceramic body and nickel-plated copper caps are designed to carry heat and withstand a much higher voltage across one assembly. The 14 mm, 31 mm and 45 mm families cover progressively higher power and voltage. The bar is normally chosen for a bleeder chain, equalising network, high-voltage supply, test system or energy-dump position where a PCB resistor cannot provide enough creepage, surface area or terminal strength.

Choosing resistance, voltage and power together

Start with the maximum continuous voltage across the individual resistor, not only the total voltage of the equipment. A divider can use several resistors in series so that each body sees a controlled share of the field. The selection must then account for the resistor tolerance, the voltage coefficient, the expected temperature rise and the clearances around each terminal. A nominal 100 kV system does not automatically require one 100 kV resistor; it may require a series string with equalising geometry and a defined insulation system.

Power is calculated from the actual voltage across the resistor and its resistance: continuous dissipation follows P = V²/R, while a pulse must also be checked by energy, pulse width, repetition rate and cooling time. A resistor that survives one short test pulse may still overheat in a repetitive waveform. For a laser PFN, crowbar, X-ray generator or capacitor-discharge system, send the waveform and repetition rate with the RFQ instead of selecting only from the catalogue wattage.

Tolerance also has a system meaning. In a voltage divider it sets the measurement error and the balance between series elements. In a bleeder chain it affects the steady-state voltage distribution. In a precision meter it can be more important than the maximum resistance. HVC can quote tighter tolerance, custom values and a matched set when the application needs a defined ratio rather than independent catalogue pieces.

Planar, tube or power bar: selection boundaries

Choose the planar leaded body when the resistor must fit a PCB or a compact radial assembly, the resistance is high, and the heat can leave through the board, air or an adjacent mounting surface. Choose the cylindrical tube when the available space is axial and the part will be supported by leads, an insulating sleeve or a custom fixture. Choose the power bar when voltage, wattage, terminal strength or creepage dominates the design and the customer has room for a larger ceramic body.

Do not replace a planar or tube resistor with a power bar only because the power rating looks higher. The cap, stud, lead spacing, insulation distance and thermal mounting may be incompatible. Likewise, do not replace a power bar with several small leaded resistors without checking the series voltage distribution, the field around the connections and the heat balance. HVC treats a replacement as a mechanical and electrical match, not as a resistance-number match.

High voltage resistor applications

In medical X-ray and CT generators, high voltage resistors are used in divider networks, feedback circuits, bleeders and protection paths. The resistor must remain stable through the generator duty cycle and must not add excessive inductance to the measurement or protection loop. In NDT and industrial inspection equipment, the same issues appear at higher mechanical stress because the generator may run for long periods and the cabinet environment can be warm or contaminated.

Laser power supplies, Marx generators and pulse-forming networks impose a different requirement. The waveform can have a steep edge, so parasitic inductance and distributed capacitance affect the pulse shape. A non-inductive thick-film construction is usually preferred for the resistor positions that shape, damp or measure the pulse. The final choice still depends on peak voltage, pulse energy, repetition rate and the required number of cycles.

High voltage power supplies also use resistor chains for discharge, voltage grading and equalisation. These positions are often overlooked during replacement because the equipment still works at no load. During shutdown or a fault, however, the chain controls stored energy and voltage distribution. The replacement must therefore match the original power duty, insulation system and physical spacing, not only the printed resistance value.

Power bar sizes and ratings

The power bar is the only form factor that reaches 150 kV as a single part. Three bar diameters cover the range:

바 직경연속정격 출력최대 전압
14 mmHVRPFS81 / 110 / 156최대 25 W80 kV
31 mmHVRPFS158 / 160 / 208 / 210 / 308최대 55 W100 kV
45 mmHVRPFS310 and above최대 110 W150 kV

All three run 200 Ω to 1 GΩ, tolerance from ±0.1%, −40 °C to +175 °C, power endurance 1,000 h at rated power with ΔR ≤ ±0.15%. Bar diameters of 16 and 21 mm are also available between the three standard sizes.

Which form factor for which job

Duty일반적인 사양이곳에서 시작
X-ray and CT high voltage divider20–35 kV, 0.1% ratio, low TC, non-inductivePlanar leaded
Bleeder and equalising chain in an HV supply60–150 kV, watts of dissipation, axial or screw mounting파워바
Crowbar and energy dumpHigh pulse energy, low inductance, screw terminalsDisc resistors
Compact axial space in a probe or multiplierUp to 60 kV in a 3.5–7 mm body원통형 튜브
Precision metering and calibration±0.1%, 1 GΩ–1 TΩ, low voltage coefficientPlanar, high value

What non-inductive means in practice

A non-inductive resistor does not mean that the complete assembly has zero inductance. Leads, caps, mounting hardware and the surrounding wiring still contribute parasitic values. It means the resistive element itself is not wound like a coil, so the part avoids the large inductive behaviour associated with a conventional wirewound resistor. This distinction matters in fast dividers, snubbers, pulse generators and protection networks.

The installation still has to keep the high-current or high-voltage path short. Place the terminals so the field is not concentrated at a sharp edge, keep the required creepage and clearance, and avoid routing a return conductor directly beside the high-voltage end unless the design calls for that geometry. HVC can review a drawing when the resistor is part of a high-frequency or high-energy assembly.

Non-inductive by construction

All three families are thick film on ceramic, not wirewound, so there is no coil to store energy. In a crowbar, a laser PFN or a fast divider this is the difference between a clean edge and a ringing overshoot. If a circuit needs a defined inductance, ask for it explicitly; the standard parts are specified as non-inductive.

How HVC handles a replacement request

A useful replacement starts with the original part number, but the part number is not enough for a high voltage resistor. Send the original datasheet or drawing when available, together with the voltage across the part, the resistance and tolerance, the continuous or pulse power, the body envelope, the terminal arrangement and the operating environment. A photograph is useful for identification, but the electrical and mechanical requirements determine the final recommendation.

HVC compares the original and proposed part in four groups: electrical, thermal, mechanical and supply. Electrical comparison covers resistance, tolerance, voltage, power, pulse and voltage coefficient. Thermal comparison covers the ambient temperature, mounting condition, derating and heat path. Mechanical comparison covers the body diameter, length, lead spacing, cap, stud and insulation distance. Supply comparison covers samples, batch size, production lead time and the documentation required by the customer.

The result should state what matches and what does not. A part can be electrically compatible but mechanically different, or mechanically interchangeable but unsuitable for a repetitive pulse. When the available information is incomplete, HVC will mark the recommendation as pending engineering confirmation rather than calling it a direct replacement.

Replacing a discontinued high voltage resistor

Most high voltage resistors in service were designed in when a catalogue part existed. When the original brand ends a series, the board and the mounting do not change, so the replacement has to match resistance, voltage, power, body envelope and terminal. HVC builds to the original drawing and publishes the cross-reference with the offer.

The resistor replacement index covers Ohmite, EBG, Caddock, KOA, Vishay, TE/Tyco, Riedon, SRT-Restech, Nikkohm, Stackpole, Nicrom, Metallux, Ohmcraft and Micro-Ohm — over 1,000 part numbers cross-referenced. For power resistors specifically, the high power resistor range lists the EBG, Ohmite and Nicrom equivalents by wattage.

Documents, samples and production qualification

For a first evaluation, the most useful package is the electrical requirement, the mechanical drawing and the intended application. HVC can then return a proposed part number, dimensional information, the relevant test conditions and a quotation. If the resistor is used in medical imaging, industrial inspection, energy equipment or a safety-related circuit, state the qualification stage so the sample and documentation package can be prepared correctly.

Prototype samples should be evaluated in the actual mounting condition. Check resistance at the specified test temperature, verify the voltage distribution in a series string, measure temperature rise at the required duty, and inspect the clearance around the terminals. For pulse applications, test the real waveform rather than substituting a DC bench test. Production approval should also include batch consistency, packaging, traceability and change-notification requirements.

The available document set depends on the selected family and project. Typical request items include a datasheet, outline drawing, part-number decoding, resistance tolerance, temperature information, test records, RoHS or REACH documents where applicable, and sample confirmation. Ask for the exact files needed by your supplier-qualification process when submitting the RFQ.

견적을 받기 위해 무엇을 보내야 할까요?

자주하는 질문

What is the highest resistance available?

1 TΩ in the planar family. Above that the value is limited by surface leakage and by the voltage coefficient, so the practical ceiling depends on the applied voltage.

Can one resistor cover 150 kV?

Yes, in the 45 mm power bar. Above 150 kV, series strings are built to drawing and the mechanical length becomes the constraint.

Thick film or wirewound for high voltage?

Thick film for anything fast or high in value: it is non-inductive and reaches teraohms. Wirewound is only sensible where the resistance is low and the pulse energy is large.

Do you supply single units for evaluation?

Yes. Prototype quantities are quoted the same way as production, with the test data for the delivered lot.

리드 타임은 무엇입니까?

Standard resistor ranges are typically scheduled at about 3 weeks from order; quotations are returned within 6 hours. Final timing is confirmed against the selected resistance, voltage, power, quantity and delivery location.

Specifying a high voltage resistor?

Send resistance, working voltage, power and the body envelope. HVC replies with a matched part number, the test data and a 6-hour quotation.

기술 견적 요청 →